☎ +86 13392540241 ✉ sale@labellet.com 🕒 26 yrs label experience  ·  ISO 9001 CERTIFIED

BUS WRAP VINYL · FULL-SIDE FLEET FILM · 0.914–1.52 M ROLLS

Bus Wrap Vinyl for Full-Side Fleet Advertising

The liner has diamond vents, so one crew can lay a full bus side flat in a single night shift. We stock six films in four glue colours, with laminate for buses that wash every day.

≤ 3 bubbles per m² after lay-down5-yr polymeric outdoor life1.52 m widest single-piece flank drop

Labellet, Bus Wrap Film Manufacturer in China

A bus side is the biggest outdoor panel you can buy. It gets washed every day and rehung every few months. We make film for that life: city buses and coaches, curved tails, accordion joints, night-shift swaps and soap-heavy wash routes. The liner carries a diamond pattern that feeds air out as you squeegee, so the face sits flat like normal vehicle vinyl. We cut five widths ourselves, 0.914 to 1.52 m. Which face, glue and liner to use is all in the Spec table.

Clean Full-Panel Removal After 3–12 Months on Route

Most bus ads stay up 3 to 12 months. When the job is done the whole side needs to peel off in one go, leaving the paint clean underneath. Before we ship anything we pull test panels three ways: what the panel looks like after the strip, whether the tack lasts the full months on the road, and how much the edge lifts at highway speed. If it sticks fine but leaves glue behind, we will not sell it as bus wrap.

Five Stock Widths for Seam-Free Flanks, Slit at 1300 mm

A splice always tears first at the next changeover, so flanks, tails and box bodies hold up better in one piece. We slit and rewind on our own 1300 mm line and keep 0.914 to 1.52 m rolls in 50 m lengths on the shelf. Every width cuts clean in one pass. A 1.37 m or 1.52 m roll will cover a standard flank top to bottom, no joint down the middle.

130 µm Polymeric Face Plus High-Tack Removable Glue, Stock in 7 Days

Our main film is 130 µm polymeric PVC on high-tack removable glue. It lives outdoors but still bends round window bands, wheel arches, tail curves and rivet lines. Edges stay down for the whole campaign, then lift off without marking the original paint. Stock rolls go out in 7 days at 1 roll MOQ. Production and custom times are down in the FAQ.

Hung between two timetables

Bus wrap for flanks, tails, joints, changeovers and wash lines

Five jobs we run into all the time. Below is what film we use, how thick, and how we lay it so the bus still rolls out in the morning.

B1 · Full-Side FlanksFull Side Bus Wrap for Fleet Advertising Panels

Side flanks are big and the workshop window is tiny. Most depots hand you one night. The bus has to run early next morning, so there is no second chance. We start in the middle and work outward, pushing trapped air through the channels until the sheet sits flat. P-1241 does most fleet sides. P-1018 is the one we put on brand buses that stay wrapped for years. Both are 130 micron polymeric, so you lose a bit of stretch but gain outdoor life. Check lamp holes on the drawing before cutting. Match the glue to one media cycle and the old graphics pull off clean. Strip numbers are in the Testing table below.

  • Mostly city-bus flanks, coach sides, rear quarters, full-fleet changeovers.
  • We send P-1241 / P-1018 wide rolls for one-piece drops — 1.52 m covers most flank heights.
  • Shade or night work only. Hot steel grabs fast and kills venting time, so close the edge with heat the B5 way.

B2 · Rear Ends & Tight CurvesBus Rear Wrap Film for Compound Curves and Lamp Clusters

Tail panels fail late. Not on day one. Two to four weeks later. Curves, lamp pods, grilles and weld seams lift the film into hollow pockets. Road shake and wash water work those pockets until the patch drops. We cut by radius and keep each piece under a third of the arc. Lamps and handles get cut out, never bridged. And we never leave the final cut on the face, because that score line is where the next strip starts to tear. Our 130 micron face bends round a 10 mm radius. Anything tighter gets thin 85 micron P-1215, cut small to the survey drawing.

  • Mostly curved tails, front caps, lamp surrounds, grille and seam zones.
  • For arc pieces we slit P-1241 narrow at 0.914 / 1.07 m, and anything under 10 mm goes to P-1215.
  • Ring-cut each lamp root while warm. Fix the split lines on the survey drawing before anyone climbs up.

B3 · Articulated & Double-DeckersArticulated Bus Wrap Joints and Double-Decker Section Breaks

Long buses never sit still. The bellows on an articulated bus folds at every turn. Top and lower decks on a double-decker push against each other all day. One sheet across that joint holds for a week, then it gives up. We cut the film at the bellows and press both sides down. The picture still lines up, but each side moves on its own. On double-deckers we hang two separate drops and hide the joint on a body seam, never out in open panel. Any long straight joint goes on a pillar or rub rail where the body line takes it. A seam left in flat paint shows from across the road and washes off first.

  • You see it on bellows zones, double-decker breaks, anything 12 m and up.
  • We match the roll to each section height instead of cutting from habit.
  • Nothing runs straight across the bellows — break it, seal both edges, keep the picture lined up and let each side move.

B4 · Quarterly ChangeoversRemovable Bus Wrap for Quarterly Fleet Changeovers

How you strip decides if the next wrap sticks. Short runs take standard removable, long edges and winter storage want high-tack. The exact grade is under Custom 05. Push a grade past its rated months and the glue locks into the paint. Then you are scraping, not stripping. Pull slow at about 45 degrees, never straight up. Dab leftover glue with remover, not a blade. Wash the panel and let it dry, because any solvent left behind turns into a release layer for the next drop. And never strip a bus fresh from the sun. Let it cool to 15 to 30 C or you double the residue.

  • Quarterly and half-year rotations, five-bus batches, depot night-shift strips.
  • Short flights get standard removable, long edges get high-tack P-1241 / P-1242 — exact grade is under Custom 05.
  • Keep a rolling buffer on the shelf so the next flight and rush top-ups are covered.

B5 · Daily Wash LinesWash-Resistant Bus Wrap With Overlaminate for High-Frequency Routes

A city bus sees more soap in a month than a box truck sees in a year. Daily passes, alkaline soap, spinning brushes, sometimes a pressure lance. The wash hits the edge first and the print second. So we seal the edge and put a throwaway layer on top. Each edge gets wrapped 5 to 10 mm and set with heat, so soap cannot creep under the glue. Then the print gets covered with B-1013 gloss or B-1014 matte laminate. That laminate takes the beating. Bare print chalks out in weeks on the same route. If a depot washes more than once a day, put the soap name in the contract and hold the first bus 30 days before you release the rest.

  • Daily wash routes, depots on alkaline soap, pressure-lance top-ups.
  • Every wash-route drop gets B-1013 gloss or B-1014 fine-matte on top — wash numbers are in the Testing table.
  • Put wash times and soap on the quote first. That is what picks the laminate, not habit.

Running alkaline wash lines? Say so up front — those drops need a laminate. Ask which laminate.

6 builds, one table

Bus wrap spec: 6 films, gauges and glue colours

Face, thickness, glue, liner and roll size for each build, plus which bus job it fits. Thickness is face plus glue only — liner does not count.

ModelFace stockTotal gaugeAdhesiveLinerRoll sizeStocked for
P-1241White high-gloss PVC, polymeric130 ± 10 µmHigh-tack removable, grey140 g single-PE diamond0.914 / 1.07 / 1.27 / 1.37 / 1.52 m × 50 mFull-side flanks; workhorse bus wrap
P-1018White high-gloss PVC, polymeric130 ± 10 µmHigh-tack removable, grey140 g single-PE diamondSame widths × 50 mMulti-year brand routes, 5-yr outdoor
P-1242White high-gloss PVC, polymeric140 ± 10 µmHigh-tack removable, black140 g single-PE diamondSame widths × 50 mDark bodies, corrugated skins, old-livery cover
P-1104White high-gloss PVC, monomeric140 ± 10 µmRemovable, white100 g single-PE diamondSame widths × 50 mPale bodies; white glue lifts opacity
P-1215White high-gloss PVC, monomeric85 ± 10 µmRemovable, grey120 g single-PE diamondSame widths × 50 mWindow frames, arches, sub-10 mm radii
P-1266White high-gloss PVC, monomeric180 ± 10 µmRemovable, clear140 g single-PESame widths × 50 mStiff wide drops, low-support beds

All six run the same diamond venting, slit 0.914 to 1.52 m by 50 m. Long outdoor life means polymeric. Short money-saving runs can live with monomeric. Most fleets run grey. Black hides dark or patched paint, white lifts pale paint, clear leaves the panel showing.

Fleet custom program

Custom Bus Wrap Film for Articulated and Double-Decker Buses

Eight variables decide price, lead time and install result. Confirm once and we quote with test sheets attached.

01 · Channel depth & density

Big flat sides want a deep channel that clears air fast. Tail curves and small lettering want a shallow one that stays invisible. We set channel depth against glue hardness when you order.

02 · Face resin system

Much past six months outside, use polymeric. For a short promo you can save money with monomeric. Cost against outdoor life is broken down in the note under the Spec table.

03 · Total gauge

85 micron for window frames and tight corners. 130 micron does most side panels. 140 micron stays flat over corrugation. 180 micron spans big open boards. Thicker holds shape, thinner bends easier.

04 · Adhesive colour

Pick glue by what you need to hide. Black covers old paint, white lifts pale bodies, grey does most fleet work, clear leaves the panel showing. The Spec note has the full rundown.

05 · Tack grade

Short runs take standard removable for 3 to 6 months. Long edges want high-tack for 6 to 12 months. Past a year we go semi-permanent and plan a remover wash at strip-off.

06 · Liner weight

Wide sheets stay flat on heavy 140 g liner. Narrow drops go down faster on light 100 to 120 g liner. Release is matched to the glue on every run.

07 · Width, length & cutting

Tell us your tallest straight drop and we cut so joints land on pillars or rub rails. Slots, marks and contour cuts follow your drawing. Bellows and handles arrive with the cut-outs done.

08 · Overlaminate & pack

Buses on daily wash get gloss B-1013 or matte B-1014 on top. Rolls ship from Shenzhen / Zhuhai to land on your install date.

Real test numbers, not brochure words

How our bus wrap tests: venting, strip, wash and weather

Each line below is something we actually ran — ask for any sheet by name. We test to FINAT FTM, ASTM and GB/T. Xenon ageing and B1 flame come with the job when you need them.

PropertyTest Standard / MethodLabellet Typical Value
Air release, laid sample1 m² squeegee lay-down, 24 h visual≤ 3 residual bubbles per m² over 3 mm dia.
Total gauge, workhorse flankFace + glue bed, liner excluded130 ± 10 µm (P-1241 / P-1018); 85 / 140 / 180 µm on option
180° peel, stainlessFINAT FTM 1 / ASTM D3330 / GB/T 2792High-tack removable 8–15 N/25 mm
Loop tackFINAT FTM 9≥ 10 N/25 mm
Shear holdFINAT FTM 8, 1 kg static≥ 48 h
RemovabilityFull-sheet strip inside rated cycleComes off in one sheet inside its rated months. We keep strip photos on file for the factory cards.
Residue checkASTM D3359 cross-hatch after stripGrade 5B, paint stays clean with no ghosting
Edge hold, 90 daysHigh-speed airflow + wash exposureEdge lift ≤ 2 mm
Alkaline wash resistanceWash-line detergent, 50 cycles50 alkaline washes: edges stay down, gloss stays, print stays
Pressure-rinse resistance80 bar at 300 mm80-bar rinse at 300 mm: no lifted edges, no water under the film
Ink adhesionASTM D3359 / ISO 11339 cross-hatchGrade 5B, no coating loss
WeatheringISO 4892-2 xenon exposurePolymeric approx. 5 yr vertical south-facing; ΔE ≤ 3.0 with bond held
Dimensional stability70 °C × 24 h, free shrinkage≤ 0.5% (calendered face)
ConformabilityCurve wrap checkSits round a 10 mm radius, no bridging over rivets and seams
Service rangeChamber cycling−40 °C to +80 °C, winter depot cold to sun-baked flanks
Install windowPanel + ambientNeeds 10 °C and up; sweet spot is 15–30 °C (warm the steel, never the film)
Printer compatibilityPress-room verificationRuns on SOL / ECO / UV / LATEX and photo machines, corona + coated face ready to print
Flame ratingOn request per projectB1 to GB 8624 for interior transit trims, we test it per job

Want the full test sheet behind any line? Email sale@labellet.com with your bus type, drop height and cycle length. We reply within 24 hours.

Why fleets buy from Labellet

1000+ fleet customers keep coming back

Six films and four glues made in one plant — plus we actually keep the test sheets.

Bubbles get counted on real panels

Every batch gets laid on a test panel and counted after 24 hours. Tack too. The sheet rides along with your rolls.

Strip numbers ride with the roll

Peel, tack, 48-hour hold and the 90-day edge check go in the box. Months on your paper do not match what we quoted — send it back.

Wash film soaks fifty times first

Wash-route film does fifty alkaline cycles plus the 80-bar rinse before we let it out. Pass or fail, it is on record.

Cut wrong? We swap it

Poly and mono are priced separately and cut to your tallest drop. Roll does not fit your drawing — we swap it.

Request Free Sample

Bus wrap swatches P-1241 / P-1242 / P-1215 · replies in 24h

No spam. Prefer email? Write to sale@labellet.com

Which film for which job

Pick the right bus wrap in 30 seconds

Eight jobs buyers ask about most. Spot yours, take the film next to it, and the quote starts there.

ApplicationMatched buildWhy this one
Full-side city-bus advertisingPolymeric 130 µm grey (P-1241)One drop covers the flank top to bottom, and the old ads strip off clean.
Long-term brand routes (12 mo+)Five-year polymeric (P-1018)Made to sit outside for years. Just plan a remover wash when it finally comes off.
Dark bodies & corrugated sidesBlack-adhesive 140 µm (P-1242)Hides old paint and dark panels, and sinks down into the valleys.
Pale bodies & pale bedsWhite-adhesive 140 µm (P-1104)Lifts the colour on light paint and keeps short runs cheap.
Tail curves, lamps & grillesNarrow-slit P-1241 + thin P-1215Cut it in arcs. The 85 micron film takes curves under 10 mm.
Articulated bellows & deck breaksSection-matched widthsFilm stops at the joint while the picture still lines up.
Window frames & wheel archesThin 85 µm grey (P-1215)Bends round tight edges where thick film just will not sit.
Daily wash routesAny face + B-1013 / B-1014The top laminate takes the brushes and the soap.

Before you ask for a price

FAQ

For buyers, fleet managers and the crew that lays the film.

1What size do the rolls come in?

Six films in the Spec table, five widths, all 50 m long. P-1241 is our main flank film at 130 plus or minus 10 micron for face and glue, on 140 g diamond liner. It prints on SOL, ECO, UV and Latex. You can start at 1 roll. Stock goes out in 7 days, standard runs in 15 days, full custom in 45 days. We ship from Shenzhen / Zhuhai.

2Six films — which one do I actually need?

Five things decide it: panel shape, months on the bus, body colour, curve size and wash. Plain fleet sides run grey P-1241. Brand buses that stay out for years want P-1018. Dark or patched paint wants black P-1242. Light paint wants white P-1104. Curves under 10 mm want thin P-1215. Big flat boards with no backing want P-1266. Tack grades sit under Custom 05.

3What width fits my bus?

Cut to the panel, not to habit. Plain flanks go 1.37 or 1.52 m in one piece. Window bands, tails and bellows follow the bus table under this FAQ. Glass needs perforated window film — this series is for the body panels.

4Glue comes in grey, black, white, clear — does it matter?

Only for hiding, not for stick. Dark or patched buses call for black P-1242. Light paint calls for white P-1104 to lift the colour. Most fleet work is fine on grey. Clear is for jobs where you want the panel showing through. The full rundown is in the note under the Spec table.

5My buses wash every day — what holds up?

Put wash times and soap name on the quote — that picks gloss B-1013 or matte B-1014. On the bus, wrap the edge with heat and keep the print covered. That is the B5 way. Wash numbers are in the Testing table.

6Why do edges lift even on air-egress film?

It is almost always the same three faults. Panel was dirty or wet. Steel was too hot or too cold. Edge never got its 5 to 10 mm heat seal. Channels clear air in the middle but they cannot save a loose edge. Tell us how you prepped, what the panel temp ran, and how you closed the edge, and we can usually spot it straight away.

Bus type vs width: what to slit before the night shift
Bus type & zoneSuggested widthSplit note
Standard flank, 1.2–1.5 m tall1.37 / 1.52 mSingle-piece flank height, no lengthwise seam
Flank with window band1.07 / 1.27 mBelow- and above-window boards split; glass takes perforated window film
Curved tail, double curvature0.914 / 1.07 mArc-split pieces, each under a third of arc length
Articulated bellows sides0.914 mMaterial broken at bellows, pressed both sides
Double-decker upper / lower1.52 mTwo independent drops, joint on structural seam
Window frames & tight trims0.914 mThin P-1215 for narrow shaped zones

Send your tallest panel height. Film matched in 24 hours.

Bus type, panel height, body colour, months on the road, wash times. Send those five and we come back with film, thickness, test sheet and price.

Request Free Sample
Email
WhatsApp
WhatsApp QR code
WeChat
WeChat QR code
Labellet Manufacturer
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.