☎ +86 13392540241 ✉ sale@labellet.com 🕒 26 yrs label experience  ·  ISO 9001 CERTIFIED

WHITE PVC · REMOVABLE ADHESIVE · 914–1520 MM · MOQ 1 ROLL

Dance Floor Vinyl Wraps for Weddings, Banquets and Brand Events

Calendered white PVC film printed to your artwork and cut to your module size. It stays flat through the event and lifts off clean for venue handover.

90–150 µm calendered white PVC5 widths 914–1520 mmMOQ 1 roll stock in 3–7 days4 adhesive colours clear / white / grey / black

CALENDERED, CUT TO MODULE, TRIAL-LAID BEFORE IT SHIPS

Labellet — Dance Floor Vinyl Wraps Manufacturer in China

A dance-floor film usually fails in three familiar places. Grid lines break at the seam. The face turns slippery on polished stone under a full room. The adhesive lifts during the event or leaves residue after it. Thin event vinyl cannot fix any of these, and neither can printed carpet.

Labellet supplies the film as a matched set. Facestock is calendered white PVC in 90, 120 or 150 µm. Adhesive follows the substrate and the removal time. The composite face is textured for grip, and the overlaminate follows lighting and camera work. Cut to module, it keeps grid lines true under stage light and strips clean for handover. The order below is the order you specify in: models, venue and substrate, then the nine settings that adapt the build.

Module Layouts Calculated From Your Artwork and Module Size

Dance floors usually tile in 2 m x 2 m or 3 m x 3 m modules. Send the artwork and module dimensions and Labellet marks out each width inside the layout, with registration marks pre-printed at module size. Each of the 914 / 1070 / 1370 / 1520 mm widths covers its own module range, so grid lines stay straight under stage light with no on-site trimming.

Composite Anti-Slip Tested on the Actual Floor

Anti-slip texture, composite face and adhesive are matched to each other. Each combination is trial-laid on polished marble, terrazzo or timber and checked for friction before shipment. Grip measured on the real substrate is what keeps the floor flat under a full room.

Hold During the Event, Clean Release After It

Residue after removal, initial hold and seam behaviour are tested together under guest load, trolley traffic and heel pressure. The floor stays flat through the event and strips clean for handover.

WHITE FACESTOCK, WEDDING PARTY SPEC

Dance White Vinyl Floor Wrap for Wedding Party: Why the Base Is White

All seven models use the same white facestock. For wedding work this matters more than any other line on the data sheet. White holds the highest contrast a dance floor can print: grid lines stay crisp, pale marble veining stays visible from the far end of the room. The overlaminate adds saturation on top. A dark or coloured base can only reduce that contrast, so bright colour should sit in the ink, not in the film.

Guests read the floor from across the ballroom, not from under their feet. A pattern that looks fine at ankle height often goes flat in photos taken from the top table. White keeps the artwork legible at that viewing distance.

Finish decides how much of that contrast survives under lights. Gloss throws the rig straight back at guests and cameras, and pale patterns wash out in the reflection. Fine matte scatters the light, so lines hold and colour stays put. Hiding the venue floor underneath is a separate task for the adhesive behind the film: white, grey or black adhesive covers the ground, the face stays white for print.

SEVEN STOCKED MODELS

Which Dance Floor Vinyl Wrap Model Fits the Floor and the Removal Plan

All seven use the same base: white calendered PVC, removable adhesive, 120 or 140 g liner, five widths from 914 to 1520 mm, one-roll minimum. Adhesive colour and total thickness are what differ, and those two lines pick the floor and the release.

ModelGradeThicknessAdhesiveRelease linerWidths × roll lengthWhere it earns its place
P-1057Removable white gloss, clear adhesive90 µm ± 10 µmClear removable120 g single PE914 / 1070 / 1370 / 1520 mm × 50 mThe reference grade. Cleanest release on polished stone and timber.
DF-1090-WDance-floor white gloss, white adhesive90 µm ± 10 µmWhite removable120 g single PESame widths × 50 mDark grounds where the floor colour needs covering.
DF-1090-GDance-floor white gloss, grey adhesive90 µm ± 10 µmGrey removable120 g single PESame widths × 50 mThe balance grade between light and dark grounds.
DF-1090-BDance-floor white gloss, black adhesive90 µm ± 10 µmBlack removable120 g single PESame widths × 50 mFull light blocking, covers floor colour and soiling.
DF-1090-MDance-floor white fine matte, clear adhesive90 µm ± 10 µmClear removable120 g single PESame widths × 50 mLess glare under stage light, seams barely visible.
DF-1120-HThickened high-tack removable120 µm ± 10 µmHigh-tack removable, clear140 g single PESame widths × 50 mGrass, gravel and mildly uneven sub-floors.
DF-1150-PThickened permanent high-tack150 µm ± 10 µmPermanent high-tack, clear140 g single PESame widths × 50 mProp floors and fixed installations, never stripped.

APPLICATION SOLUTIONS

Dance Floor Vinyl Wraps for Weddings, Outdoor, Brand Events, Film Sets and Rentals

The white base stays the same across all five. Substrate, module plan and removal time carry more weight than the print. Only adhesive, thickness and overlaminate change job to job.

L1 — Hotel Banquet Halls and Wedding ReceptionsDance Floor Vinyl Wraps for Hotel Banquets and Weddings

P-1057 + B-1013 · 2 m module cut from a single width

Banquet halls run more dance-floor film than any other venue, under the tightest handover. Floors are polished marble or terrazzo, the room often turns around within hours, and the stage plus dance floor usually sits on a two-metre grid. Columns, light troughs and floor boxes break up the rectangle, so each layout is drawn around fixed obstructions.

  • Clear removable adhesive P-1057 on both light and dark marble, so nothing is left covering the floor when the film comes off.
  • For light patterns on dark polished stone under direct stage light, use fine matte overlaminate B-1014. Gloss B-1013 glares in that spot.
  • Where the venue floor is carpet, fibre grip and adhesive wet-out occur together, so an adhesion and removal sample is made before the order enters production.

L2 — Outdoor Grass Weddings and Terrace PartiesAnti-Slip Dance Floor Vinyl for Outdoor Weddings on Grass and Terraces

DF-1120-H + B-1004 · 120 µm fills ground relief

Outdoor weddings lay on temporary PE ground sheet, grass or gravel. Edges are open and outlines irregular. Rain, dew and day-night temperature swings move the film and lift edges. Grass stalks leave hollows under a 90 µm face, so open uneven ground needs a thicker build that bridges the relief.

  • Open uneven ground needs the thicker build to bridge the relief.
  • A laid PE sheet counts as a separate substrate from open grass or gravel.
  • Outdoor jobs add weather cover on top of the substrate choice: the face has to handle dew, daylight and foot traffic together.
  • Wet grip and clean release get checked together on the real ground before the run starts.
  • For night photos, matte keeps spill out of the lens where gloss throws it back.

L3 — Brand Launches and Themed Dance FloorsCustom Printed Dance Floor Vinyl for Brand Activations and DJ Stages

DF-1090-B · full light blocking

Brand launches and themed parties buy the floor for the look, not for protection. Moving spots sweep across the graphic under DJ lighting, so colour shift under hard light is the acceptance test. Most jobs print bright artwork on a black or deep grey ground, or switch to matte to hold reflections down.

  • Black adhesive DF-1090-B blocks the ground colour and soiling completely.
  • Matte facestock across the stage and dance area to cut the spill of the light spots.
  • On artwork with tight tolerance, a 1:1 print sample is run before the press to check the tonal ladder and confirm the ink system matches the overlaminate.
  • Internal-light dance floors need the black adhesive grade to block light, so lamp hotspots do not come through the artwork as bright patches.

L4 — Film Shoots and Prop Dance FloorsDance Floor Vinyl for Photo Shoots and Film Sets

DF-1150-P · permanent bond, low-odour adhesive

Film and photo sets judge the floor through the lens. Graphics must hold shape on camera while the material survives repeated handling, rolling and overhead hangs. The film often shares the room with actors, make-up and food, so odour and volatiles are checked on the sample before approval.

  • Low-odour, controlled-volatilisation adhesive, with an odour assessment on the sample stage.
  • Prop floors use the permanent high-tack grade so the edges do not lift and shift in transit.
  • Where the film has to be formed over a curve or into a box, fine matte or coarse matte facestock hides the reflection lines that a gloss face makes obvious.
  • Approval covers graphic stability and odour. Event-floor residue rules do not apply here.

L5 — Rental Companies and Repeat TurnoverRemovable Dance Floor Vinyl for Event Rental Companies

MOQ 1 roll · 914 / 1270 / 1520 mm in stock

Rental companies hold the floor as stock. Rolls sit for months or years, get cut and printed before each event, and move between venues. What counts here is clean release after long storage, no creasing through repeated rolling, and batch numbers traceable in the warehouse.

  • Stock rolls are stored by batch number and width, with the adhesive side rolled out, so no adhesive transfers inside the roll over long storage.
  • Three widths 914 / 1270 / 1520 mm cover the common module sizes while keeping the inventory volume down.
  • We check each roll for liner damage and creasing before use; we replace any section with a split liner before the next event.
  • Supply is normally a rolling monthly order against a 7-day stock cycle, so a rental inventory can be topped up between bookings with no per-event production run.

BUILT AROUND THE FLOOR

Custom Dance Floor Vinyl Wraps in 9 Decisions

The stocked builds are in the table above. Nine settings adapt one of them to your floor. Send module size, artwork file and removal deadline and the quote comes back with no follow-up questions.

01 - Surface Form

Gloss / fine matte / coarse matte. Gloss gives the highest saturation and suits a conventional banquet hall. Fine matte cuts glare and seam visibility under strong stage light and on camera. Coarse matte gives a sand-blasted hand and suppresses fingerprints.

02 - Thickness

90 / 120 / 150 µm. Ninety fits flat indoor floors and indoor displays. The 120 and 150 µm grades fill the micro-relief of sandy cement, damaged stone and temporary ground sheets, and raise the crease resistance. The cost is a heavier roll and a larger winding radius, and higher shear force on the substrate when the film is pulled off.

03 - Adhesive Colour

Clear / white / grey / black. Clear leaves the cleanest result on light stone and timber. White gives strong coverage on a dark ground, grey sits between the two, and black blocks light completely and is used for internal-light dance floors and for covering floor soiling.

04 - Tack Grade

Removable / high-tack removable / permanent high-tack. Use removable where the floor strips and hands the venue back. High-tack removable is for grass, gravel and uneven ground. Permanent high-tack is for prop floors and fixed installations.

05 - Liner Weight

120 / 140 g single PE. Large-area lays take the 140 g liner to reduce creasing; small venues take the 120 g liner because it is easier to handle by hand.

06 - Width and Roll Length

914 / 1070 / 1370 / 1520 mm, roll length cut to the order. The dance-floor tile size and the width of the pattern repeat fix the width together.

07 - Pattern Registration and Slitting Position

Registration plan drawn per width from the customer artwork, with marks pre-printed at module size. Pattern shift shows first on the finished floor, so alignment is the primary control point on a dance-floor order.

08 - Anti-Slip Level

Composite face texture set to the use case. Heavy footfall plus spilled drinks calls for a higher grip level. Removal is checked against the same build, since grip and release pull in opposite directions.

09 - Overlaminate and Packing

B-1013 / B-1014 / B-1004 / B-1005 / B-1010, with a choice of roll packing or kraft wrap on a rigid core. High-wear and high-traffic areas take the abrasion-resistant grades; outdoor and temporary sites take the anti-yellowing grades. Stock is prepared to this packing spec when the load is a full container or the crew is crossing cities.

One limit before layout: this is a coated web. Surface form, thickness, adhesive colour and tack, liner weight, width, roll length and slitting position can all move. Slitting caps at 1300 mm. 1520 mm ships from stock, and anything off-standard needs the winding plan confirmed first.

WHY LABELLET FOR DANCE FLOORS

Why Buyers Choose Labellet

Buyers come back for four practical reasons: a white base that prints true, five stocked widths that cut seams, registration planned from the artwork before cutting, and stock plus production slots that fit the event calendar.

White facestock gives the highest colour rendering

White PVC prints the widest contrast for grids and pale marble veining, with the overlaminate adding saturation on top. White, grey and black adhesives cover dark grounds underneath, so colour work and ground cover stay on separate layers.

Five widths held in stock

914 ~ 1520 mm covers 2 m and 3 m modules, continuous grid bands and irregular outlines. Fewer site joints means fewer visible breaks and fewer edges that can lift.

Registration worked out per width from your artwork

Registration plan is drawn per width from artwork and module size, so each of the 914 / 1070 / 1370 / 1520 mm widths keeps grid lines true inside its own module range. No correction is possible after cutting, so this drawing comes before the film is cut.

Delivery rhythm that matches the event calendar

MOQ is one roll. Stock leaves in 3 to 7 days, printed runs take 10 to 15 days, monthly capacity is 20,000 m². The 7-day stock cycle lets a wedding company roll stock forward and add a late booking without a new production run.

Request Free Sample

Gloss, matte and thickened swatches · replies in 24h

No spam. Prefer email? Write to sale@labellet.com

BEFORE YOU QUOTE

FAQ

1What are the installation essentials for a wedding dance floor?

Check the venue before printing. Note the substrate, floor moisture, joint and floor-box positions, and stage-light angles. Start at the back wall and work toward the entrance so the pattern runs with the room. Store every roll adhesive-side out. Strip the film within 72 hours after closing. Longer dwell time raises residue risk, so put that deadline in the contract and the handover notes.

2Which vinyl build should I choose for a dance floor?

Match four points before ordering. Substrate first: polished marble, terrazzo and timber take the standard removable adhesive, while grass, gravel and uneven ground need the thickened high-tack removable grade. Carpet always needs a sample first, since fibre grip and adhesive wet-out have to be checked together. Next the removal time: floors that hand the venue back the same night use removable, fixed or repeatedly relaid floors use permanent. Then artwork and ground cover: the face stays white for contrast, and white, grey or black adhesive hides whatever sits underneath. Last the module: pick the width from the module size and pattern repeat, and keep each module inside one width to hold seams down.

  1. Substrate. Polished marble, terrazzo, timber, temporary PE ground sheet, grass and carpet behave as six different surfaces. Smooth hard floors take the standard removable adhesive. Grass, gravel and uneven ground need the thickened high-tack removable grade. Carpet needs its own sample before any build ships.
  2. Removal window. Floors that hand the venue back use the removable grade. Fixed or repeatedly relaid floors use the permanent adhesive.
  3. Artwork and ground. The face stays white for contrast. White, grey or black adhesive hides the floor underneath.
  4. Width and module. Pick the width from the module size and pattern repeat, and keep each module inside one width to hold seams down.
3Can the film be laid on grass, gravel or an outdoor terrace?

Yes, with a different build. Grass is open and uneven, so a 90 µm film sinks between stalks and leaves hollows. Grass, gravel and rough ground need the 120–130 µm thickened grade with high-tack removable adhesive, where the thicker glue layer beds into the relief. A laid PE ground sheet stays flat enough for 90 µm. Outdoor jobs also need a weather-resistant face plus overlaminate, rated to the south-facing vertical equivalent. After rain or dew, wet grip is checked by trial-laying on the actual ground. For night photos, the matte anti-yellowing B-1004 holds highlights better than gloss.

4What are the MOQ and the lead time for dance floor vinyl wraps?

The minimum order is a single roll, so a rental company can top up between bookings without a full production run. Widths of 914, 1270 and 1520 mm cover the common module formats and leave the warehouse inside a week. Printed jobs join the next production slot, which opens inside a fortnight. Monthly capacity is 20,000 m² on a rolling order. Widths outside stock or single-width print runs need the slitting and rewinding plan confirmed before a client date is promised.

5Should a wedding party dance floor be white or printed?

White. A white PVC face prints the widest contrast a dance floor can hold: grid lines stay crisp and pale marble veining reads from the far end of the room. The overlaminate adds saturation on top. Put bright colour in the ink. A tinted base only narrows the range. Covering the venue floor is separate work for white, grey or black adhesive, so a dark ballroom and a marble reception can print on the same white face.

6What does a wedding party order need from us before it can be quoted?

Four details close the quote first time. Module size: 2 m and 3 m modules point to the width that carries the pattern. Substrate (polished marble, terrazzo, timber, PE sheet, grass or carpet): this picks adhesive and, on rough ground, thickness. Artwork file: used to draw the registration plan per width. Removal deadline: a same-night strip and a week-long hold need different adhesives. Send these four and the spec comes back with no follow-up questions.

Still deciding between P-1057 and DF-1120-H? Tell us what you are laying the film on and how long the floor has to stay down, and we will say which of the two the job actually needs.

Send the Module Size. Get the Build Spec in 24h.

Tell us what the floor is sitting on and how long it has to stay down. You get back the model, the registration plan, the proof date and the price.

Request Free Sample
Email
WhatsApp
WhatsApp QR code
WeChat
WeChat QR code
Labellet Manufacturer
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.